FM / hisax

/usr/src/kernels/4.18.0-553.121.1.el8_10.x86_64/drivers/isdn/hisax/

/usr/src/kernels/4.18.0-553.121.1.el8_10.x86_64/drivers/isdn/hisax

Name	Size	Mode	Actions
Kconfig	12747	0644	edit dl rm
Makefile	2755	0644	edit dl rm

Edit: /usr/src/kernels/4.18.0-553.121.1.el8_10.x86_64/drivers/isdn/hisax/Kconfig (12747B)

menu "Passive cards"

config ISDN_DRV_HISAX
	tristate "HiSax SiemensChipSet driver support"
	select CRC_CCITT
	---help---
	  This is a driver supporting the Siemens chipset on various
	  ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles
	  S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many
	  compatibles).

HiSax is just the name of this driver, not the name of any hardware.

If you have a card with such a chipset, you should say Y here and
	  also to the configuration option of the driver for your particular
	  card, below.

if ISDN_DRV_HISAX

comment "D-channel protocol features"

config HISAX_EURO
	bool "HiSax Support for EURO/DSS1"
	help
	  Say Y or N according to the D-channel protocol which your local
	  telephone service company provides.

The call control protocol E-DSS1 is used in most European countries.
	  If unsure, say Y.

config DE_AOC
	bool "Support for german chargeinfo"
	depends on HISAX_EURO
	help
	  If you want that the HiSax hardware driver sends messages to the
	  upper level of the isdn code on each AOCD (Advice Of Charge, During
	  the call -- transmission of the fee information during a call) and
	  on each AOCE (Advice Of Charge, at the End of the call --
	  transmission of fee information at the end of the call), say Y here.
	  This works only in Germany.

config HISAX_NO_SENDCOMPLETE
	bool "Disable sending complete"
	depends on HISAX_EURO
	help
	  If you have trouble with some ugly exchanges or you live in
	  Australia select this option.

config HISAX_NO_LLC
	bool "Disable sending low layer compatibility"
	depends on HISAX_EURO
	help
	  If you have trouble with some ugly exchanges try to select this
	  option.

config HISAX_NO_KEYPAD
	bool "Disable keypad protocol option"
	depends on HISAX_EURO
	help
	  If you like to send special dial strings including * or # without
	  using the keypad protocol, select this option.

config HISAX_1TR6
	bool "HiSax Support for german 1TR6"
	help
	  Say Y or N according to the D-channel protocol which your local
	  telephone service company provides.

1TR6 is an old call control protocol which was used in Germany
	  before E-DSS1 was established. Nowadays, all new lines in Germany
	  use E-DSS1.

config HISAX_NI1
	bool "HiSax Support for US NI1"
	help
	  Enable this if you like to use ISDN in US on a NI1 basic rate
	  interface.

config HISAX_MAX_CARDS
	int "Maximum number of cards supported by HiSax"
	default "8"
	help
	  This option allows you to specify the maximum number of cards which
	  the HiSax driver will be able to handle.

comment "HiSax supported cards"

config HISAX_16_0
	bool "Teles 16.0/8.0"
	depends on ISA
	help
	  This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8
	  and many compatibles.

See <file:Documentation/isdn/README.HiSax> on how to configure it
	  using the different cards, a different D-channel protocol, or
	  non-standard IRQ/port/shmem settings.

config HISAX_16_3
	bool "Teles 16.3 or PNP or PCMCIA"
	help
	  This enables HiSax support for the Teles ISDN-cards S0-16.3 the
	  Teles/Creatix PnP and the Teles PCMCIA.