/
usr
/
src
/
kernels
/
4.18.0-553.157.1.el8_10.x86_64
/
drivers
/
scsi
/
aic7xxx
/
/usr/src/kernels/4.18.0-553.157.1.el8_10.x86_64/drivers/scsi/aic7xxx
mkdir
upload
Name
Size
Mode
Actions
aicasm/
-
0755
rm
Kconfig.aic7xxx
3617
0644
edit
dl
rm
Kconfig.aic79xx
3256
0644
edit
dl
rm
Makefile
2948
0644
edit
dl
rm
Edit:
/usr/src/kernels/4.18.0-553.157.1.el8_10.x86_64/drivers/scsi/aic7xxx/Kconfig.aic79xx
(3256B)
# # AIC79XX 2.5.X Kernel configuration File. # $Id: //depot/linux-aic79xx-2.5.0/drivers/scsi/aic7xxx/Kconfig.aic79xx#4 $ # config SCSI_AIC79XX tristate "Adaptec AIC79xx U320 support" depends on PCI && SCSI select SCSI_SPI_ATTRS help This driver supports all of Adaptec's Ultra 320 PCI-X based SCSI controllers. config AIC79XX_CMDS_PER_DEVICE int "Maximum number of TCQ commands per device" depends on SCSI_AIC79XX default "32" ---help--- Specify the number of commands you would like to allocate per SCSI device when Tagged Command Queueing (TCQ) is enabled on that device. This is an upper bound value for the number of tagged transactions to be used for any device. The aic7xxx driver will automatically vary this number based on device behavior. For devices with a fixed maximum, the driver will eventually lock to this maximum and display a console message indicating this value. Due to resource allocation issues in the Linux SCSI mid-layer, using a high number of commands per device may result in memory allocation failures when many devices are attached to the system. For this reason, the default is set to 32. Higher values may result in higher performance on some devices. The upper bound is 253. 0 disables tagged queueing. Per device tag depth can be controlled via the kernel command line "tag_info" option. See Documentation/scsi/aic79xx.txt for details. config AIC79XX_RESET_DELAY_MS int "Initial bus reset delay in milli-seconds" depends on SCSI_AIC79XX default "5000" ---help--- The number of milliseconds to delay after an initial bus reset. The bus settle delay following all error recovery actions is dictated by the SCSI layer and is not affected by this value. Default: 5000 (5 seconds) config AIC79XX_BUILD_FIRMWARE bool "Build Adapter Firmware with Kernel Build" depends on SCSI_AIC79XX && !PREVENT_FIRMWARE_BUILD help This option should only be enabled if you are modifying the firmware source to the aic79xx driver and wish to have the generated firmware include files updated during a normal kernel build. The assembler for the firmware requires lex and yacc or their equivalents, as well as the db v1 library. You may have to install additional packages or modify the assembler Makefile or the files it includes if your build environment is different than that of the author. config AIC79XX_DEBUG_ENABLE bool "Compile in Debugging Code" depends on SCSI_AIC79XX default y help Compile in aic79xx debugging code that can be useful in diagnosing driver errors. config AIC79XX_DEBUG_MASK int "Debug code enable mask (16383 for all debugging)" depends on SCSI_AIC79XX default "0" help Bit mask of debug options that is only valid if the CONFIG_AIC79XX_DEBUG_ENABLE option is enabled. The bits in this mask are defined in the drivers/scsi/aic7xxx/aic79xx.h - search for the variable ahd_debug in that file to find them. config AIC79XX_REG_PRETTY_PRINT bool "Decode registers during diagnostics" depends on SCSI_AIC79XX default y help Compile in register value tables for the output of expanded register contents in diagnostics. This make it much easier to understand debug output without having to refer to a data book and/or the aic7xxx.reg file.
Save
cmd:
run